Primera XL Manual do Utilizador

User’s ManualOptical Disc Duplicator ProXL051704-510231-(09)© 2001 All rights reserved.510231.qxd 5/17/2004 8:45 AM Page i

D. MINIMUM SYSTEM REQUIREMENTSSingle Drive Duplicator XL:• 700MHz or faster genuine Intel Pentium IV • 512MB or more RAM • PCI slot based Firewire car

1. Up to 100 blank discs may be loaded at one time into theInput Bin. 2. The Duplicator has an integrated robotic arm that "picks"one disc

Since most CD-Rs available today are of extremely highquality, you will rarely reject a disc. Nevertheless, it isgood practice to test each disc - ju

NOTE: Only the CD version of duplicators can print and recordsimultaneously. To ensure proper recording, the robotics may pausemomentarily when the CD

10 Hardware and Software Set-Up and TestingSection 2: Hardware and Software Set-Up and TestingA. CONNECTING INTERFACE CABLES1. Make sure that your PC

Hardware and Software Set-Up and Testing 114. Connect the Serial Interface cable. One end is connected tothe DB9 connector on the rear panel of the

12 Hardware and Software Set-Up and Testing7. Connect the 6-pin mini-DIN cable (included with theoptional Printer Stand) to the Printer Control Port o

Hardware and Software Set-Up and Testing 13For the Thermal CD Printer, the printer is mounted on the leftside of the Duplicator. For either printer,

14 Hardware and Software Set-Up and Testing9. Connect the other end of the 6-pin mini-DIN cable to thePrinter Control Port on the rear panel of the pr

Hardware and Software Set-Up and Testing 1512. Apply power to the printer. One end of the Power Adapteris connected to the printer's rear-panel

iiNotices: The information in this document is subject to change without notice. NO WARRANTY OFANY KIND IS MADE WITH REGARD TO THIS MATERIAL, INCLUDIN

16 Hardware and Software Set-Up and Testingb. Put a stack of blank CDs in the Input Bin (the one onthe right side).c. Press the Sequence button on the

Hardware and Software Set-Up and Testing 17i. Open the printer tray with the disc in/out button. On theInk-Jet CD Printer, this is the button with t

18 Hardware and Software Set-Up and TestingCheck one more time for printer alignment by pressing afterthe screws have been tightened down, just in cas

Hardware and Software Set-Up and Testing 196. With the Robotic Arm holding a disc just over the tray,move the printer around until aligned as close

20 Hardware and Software Set-Up and Testing3. The Welcome Screen is now displayed. Press Install andfollow the on-screen instructions.4. Re-boot your

Hardware and Software Set-Up and Testing 21F. SOFTWARE TESTThe final set-up step before starting your first job is to test theentire hardware/softwar

22 Hardware and Software Set-Up and Testing3. In the drop-down menu, go to Services.4. Click on Check Communications. You will get a dialog boxsaying

Hardware and Software Set-Up and Testing 236. Click on Robotics again.7. Select Manual Movements.510231.qxd 10/2/03 9:15 AM Page 23TOCINDEX

24 Hardware and Software Set-Up and Testing8. Deselect any components you don't have installed in thecheck boxes in Multiple System Test.9. Load

Running Your First Job 25Section 3: Running Your First JobNow that you've completed the hardware set-up, connected allcables, loaded the PrimoDV

Table of ContentsSection 1: Getting Started...1A. Choosing a Good Location

26 Running Your First JobHere's a short explanation of each Window:• Drive Status Window. Lists all of the available drives foryour computer. Y

Running Your First Job 27Test recording performs all of the operations of recording withthe drive's laser turned on to reading power. A test re

28 Running Your First JobThe Stop Button will abort any recording in progress andcause the Duplicator to transport the disc to the Reject Area. Itwil

Running Your First Job 29HINT: To copy specific tracks from the CD, highlight thedesired tracks then click the Extract Track button. Thiswill allow y

30 Running Your First Job11. Press the red Record button to start recording your copies.12. If everything worked right, the Duplicator should now bere

Interpreting the Duplicator’s LED Status Lights 31Section 4: Interpreting the Duplicator'sLED Status LightsThe LED Status Lights are located on

32Maintenance and TroubleshootingSection 5: Maintenance and TroubleshootingThe Duplicator is designed to operate for extended periods oftime with ver

Maintenance and Troubleshooting 33C. RECORDING ERRORSIf discs are not being recorded properly or are not passingverification, you will want to consul

34Maintenance and Troubleshootinga. Click Tools, Options and check the box labeled EnableBurn Proof. This option enables the drive to slow down itsrec

Maintenance and Troubleshooting 35D. TECHNICAL SUPPORTIf you have difficulties in operating your Duplicator, theprocedures in this manual and the Pri

ivInteractive Feature in this PDF DocumentThere are interactive features that will allow you tojump to different locations within the document. Eachli

36 Technical SpecificationsSection 6: Technical SpecificationsModel Optical Disc Duplicator ProConfigurations CD-R System: One (XL) or Two (Pro) CD-Rr

Technical Specifications 37Recordable Formats CD-R: CD-Audio (CD-DA), CD-ROM,CD-I, Video-CD, MP3 to CD-Audio (on the fly, no hard drive overheadrequi

38 IndexIndexApplication Window ...21, 25, 26Audio Job, Running ...

Index 39PrimoDVD SoftwareActivity Log ...25, 26Application Window...

Printed in the United States of AmericaP/N 510231510231.qxd 10/2/03 9:15 AM Page 40

Getting Started 1Section 1: Getting StartedTHANK YOU…...for purchasing the Optical Disc Duplicator Pro/XL. It is theperfect way for you to copy CDs i

A. CHOOSING A GOOD LOCATION• Place the Duplicator in a location with adequate aircirculation to prevent internal heat build up. If you will beattachi

C. IDENTIFYING THE PARTSFront Panel and TopThis illustration shows the Duplicator, its Control Panel,Buttons, LED indicator lights, Input and Output B

The LED Status Lights indicates that Power is ON and whenthe Pause Button has been pressed. They also blink in certainpatterns to indicate an error o

Note that the Thermal CD Printer attaches to the left side of theprinter and that the Output Bin is located in a different spotdue to the location of